Polyurethanes
Turbo Liner® Polyurethane spray coatings are typically used as a coating or lining.
It can be used in water tanks, secondary containment and waste water management applications.
Turbo Liner LP12
Turbo Liner® LP12 is a two component, 1:2, 100% solids, fast set, liquid applied, modified polyurea liner system for metal, concrete, fiberglass and wood surfaces.
Features and Uses
- Features:
» Seamless
» Tough and Elastomeric
» Chemical Resistant
» Low Temperature Flexibility
» Abrasion and Impact Resistant
» High Build
» Low Pressure Application
» Hardness, ASTM D-2240 91-93 ± 5 A
» Tensile Strength, ASTM 412-C 1300-1600 psi
» Elongation, ASTM 412-C 300-350%
» Tear, ASTM 412-C 175-200 pli
- Typical Uses:
» Truck Bed Surfaces
» Utility Vehicles
» Cargo liners
» Boat Linings
» Waterproof Decking
» Cargo Holds
» Horse Trailers
» Industrial Floorings
» Walkways
» Secondary Containment Lining with or without Geo Textile
» Encapsulation of Fiberglass Bodies and Polystyrene Foams
» Mold Castings
Turbo Liner PC150
Turbo Liner® PC150 is a two component, liquid applied, aromatic, polyurethane-alloy specifically designed to repair concrete and masonry substrates. The new surface will protect concrete from weather, corrosion, erosion, freeze/thaw spalling and chemical attack.
Features and Uses
- Features:
» Waterproof
» Excellent Abrasion Resistance
» Repairs Can Be Made in Hot or Cold Weather
» Rapid Cure Allows Traffic to Resume in 30 Minutes
» Remains Flexible in a Wide Range of Temperatures
» Hardness, ASTM D-2240 70 ± 5 D
» Tensile Strength, ASTM D-412* 4000 ± 400 psi
» Ultimate Elongation, ASTM D-412* 7% ± .05%
» Compressive Strength, ASTM C-42 4750 psi or 32.76 kNm
- Typical Uses:
» Hairline Cracks
» Thin, Wide or Deep Cracks
Turbo Liner PC220
Turbo Liner® PC220 is a single component, liquid applied, moisture cured, aromatic urethane polyurea elastomeric waterproofing base membrane.
Features and Uses
- Features:
» Economical
» Moisture Cured
» Proven Protection
» Seamless Waterproofing Membrane
» Hardness, ASTM D-2240 55 ± 5 A
» Tensile Strength, ASTM D-412* 950 ± 100 psi
» Ultimate Elongation, ASTM D-412* 500% ± 50%
» Tear,Die C, ASTM D-624* 250 ± 25 pli
- Typical Uses:
» Concrete
» Plywood
» Metal, Rubber, Wood, or Masonry Surfaces
Turbo Liner PC280
Turbo Liner® PC280 is a two component, very rapid setting, rapid curing, solvent free, flexible, high performance, and high solids urethane elastomeric coating that can be applied to suitably prepared interior or exterior concrete, plywood and metal surfaces. Due to very rapid gel time, Turbo Liner PC280 is suitable for applications in temperatures as low as 20°F. It may be applied in a single or multiple applications. Turbo Liner PC280 is also relatively insensitive to moisture and temperature allowing applications in varied temperatures and humidity.
Features and Uses
- Features:
» Non-Gassing
» Very rapid setting and cure
» Coats Green (Vented) Concrete
» Can Be Applied at Any Thickness
» Good Thermal Stability
» Good Chemical Resistance
» Meets USDA Criteria
» Excellent Low Temperature Flexibility
» Interior or Exterior Applications
» Recoatable
» Seamless
» Hardness, ASTM D-2240 80 ± 3 A
» Tensile Strength, ASTM D-412* 800 ± 100 psi
» Elongation, ASTM D-412* 800 ± 100%
» Tear, ASTM D-624* 300 ± 25 pli
- Typical Uses:
» Vehicular Traffic Areas
» Sundecks & Balconies
» Crack Repair
» Stalls, Wash Racks, Kennel Runs
» Exterior & Interior Pedestrian Traffic Surfaces such as Walkways, Patios, Stairways
» Interior Surfaces such as Floors, Mechanical Rooms